The report discusses a few of those gaps to this Muzzle-Loading Artillery Drill

Posted by homeimproment23234 on April 12th, 2021

These variations are:

1. IN BATTERY. When a cannon fires live ammunition, there is a recoil that infrequently takes place when the cannon is only firing blank powder fees. The cannon has to be repositioned on the gun line after it is fired. Following the command FIRE is provided, and following that the cannon has successfully fired, the control IN BATTERY is provided. Number 1 & 2 will grasp the wheel over the hub, Number 3 & 4 will grip the wheel in the back, and the Gunner or Number 5 will probably come forward and lift the trail spike so that the cannon can be moved ahead. When the Gunner is happy that the cannon is back in its initial position, the cannoneers will start the Service the Piece (that, when firing blank fees, is automatically done right after the cannon is successful fired). The Gunner might or might not offer the command to SERVICE THE PIECE.

Notice: Most artillery crews at live fire events will put markers up to help return the cannon to the exact same position each time after firing. This is sometimes accomplished by staking small wood planks across the front and sides of the wheels to act as guides for moving the cannon back into position.

2. The sighting of the gun so the projectile strikes the intended goal is of critical significance. Since three (3) minutes should elapse between once the cannon is fired and if the next round is introduced into the muzzle of the cannon, this really is the best time to do the primary sighting and aiming of the cannon. This is the most powerful time to perform the sighting as there's a threat to this Number 3 cannoneer who has their own thumb covering the vent after the dwell round was rammed. The Gunner may make one last sighting before the READY command is given to penis and prime the powder price, but the majority of the aiming should be done involving the IN BATTERY command and also the LOAD command.

3. Some cannoneers possess their live rounds assembled as they were during the War Between the States, which means that the powder charge the sabot and the projectile are attached together to one package. If this is done, there's absolutely no variation to the drill for loading and ramming the ammunitions near me. However, lots of cannoneers possess the powder switch separate from the sabot and projectile. This usually means that the ammunition has to be loaded and simmer at a two step procedure.

The very first step is stated in the drill. Number 2 will rest the worm on the axle (or hook it on the side of the carriage cheek), and turn toward the wheel that the receive the powder charge. Number 5 will bring the powder charge to Number 2, that will then introduce the powder charge into the end of the muzzle and then measure from the inside of the wheel and then return to POST place, leaving the pig behind. Number 5 will subsequently return to the Limber to obtain the projectile. The projectile is brought up like the powder charge into the Gunner, who will then teach Number 5 when to bring up the projectile to Number 2. Once the powder charge has been rammed by Number 1, Number 2 will measure back into the wheel well, hugging the edge of the wheel carefully (like the Misfire Drill) and, facing the wheel, prepare to obtain the projectile. Number 2 will choose the projectile from Number 5 just like the powder charge and place it just into the muzzle. Number 2 will then take the worm, step out of the wheel well, and return to POST position. The rest of the drill proceeds as normal.

Note: Some cannon crews who reside fire have standing hooks the worm and other implements may be hooked to outside of the wheel well. If one of them is present, Number 2 will choose the worm when stepping from the wheel well after introducing the powder charge into the muzzle and then rest/hook it into the stand so it is outside of the wheel well if the live ammunition is introduced to the muzzle.

Much care has to be taken when firing living ammunition. The rounds need to be closely scrutinized before the event to ensure they are safe. For rounds where the powder, sabot, and projectile are in one package, the package needs to be opened so each component can be assessed. Duct tape should not be used when procuring the projectile to the sabot since the glue can melt and make a mess. The narrow packaging tape with all the nylon fibers running through it's the best tape to use and is highly recommended. Bear in mind, it's more important to be safe than to reach the target!

50 Caliber lead shot is the very recommended because it causes the least harm to the inside of the cannon barrel. Steel shouldn't be used, and bolts & nuts should likewise not be used because of the prospect of damaging the barrel liner. The lead shot ought to be packed with sawdust to maintain the shot in place and prevent movement while in flight. The floor is cut off along with the wooden sabot inserted and tacked & taped into position. The top is then cut off and the sawdust and shot poured in until about 1/2 of an inch from the top of the can. Subsequently, the top edge is trimmed with brief vertical snips all the way around. The bottom of the can, which was cut off first, is then inverted (so that the dome is facing ) and put into the cover of the can. The snipped ends of the can are then folded in to fasten the top of their Canister Round.

For More Click Here