How TO Fix Printhead Error? Call-(+1) 844-403-0343

Posted by Mandy rawat on November 27th, 2019

But there is a way to fix these issues. But before fixing the issue you must know the type of error. So next we’ll know the type of printhead errors and way to fix them. But if you don’t want to do it yourself or don’t want any hassle then don’t worry you have to just call at HP printer support phone number-(+1)-844-403-0343.

Type Of Hp Printhead Errors-

Incompatible Printhead
Missing or Failed Printhead
Printhead Appears to be Missing or Damaged
Printhead Failure
The printhead is Missing, Not Detected, or Not Properly Installed
Printhead Missing
Printhead Missing or Damaged
Printhead Problem

Now we’ll understand how we can fix these issues.

First Step: Reset the Printer

Resetting the printer may clear the error message.

With the printer turned on, disconnect the power cord from the printer.
Unplug the power cord from the power source.
Wait for 60 seconds.
Reconnect the power cord to a wall outlet and to the printer.
Turn the printer on.

In the event that the printhead error message persists, proceed the following step.

Second Step: Identify your ink cartridges

The steps to troubleshoot vary by the type of ink cartridges your printer uses. Recognize your ink cartridge type, and afterwards pursue the means to determine the issue

The following steps apply to printers that use HP 932, 933, 950, 951, 952, 953, 954, 955, 956, 957, 958, 959, 962, 963, 964, 965, 966, 967, 968, or 969 ink cartridges.

Step 1: Update the printer firmware

Updating the printer firmware may resolve printhead issues. Go to Updating or Upgrading the Printer Firmware for knowing more.

In the event that the error message persists, proceed to the next step.

Step 2: Check the carriage for a printhead latch

Open the entryway to access to the ink cartridges, and afterwards decide whether the carriage inside the printer has a printhead lock.

If your carriage has a printhead latch, continue to the next step.
If your carriage doesn’t have a printhead latch, skip to Service the printer.

Step 3: Reseat the printhead up to three times

You may have to reseat the printhead up to three times.

With the printer turned on, unplug the power cord from the rear of the printer.(Important: You must disconnect the power cord before reaching inside the printer.)
Lift the carriage latch, somewhat lift the printhead, bring down the printhead once again into the carriage, wiggle the printhead left and right, and afterwards bring down the carriage latch to lock the printhead into place.
Close the ink cartridge get to entryway.
Reconnect the power cord to the back of the printer.
In some cases, error messages persist after inserting the printhead. On the off chance that the error message perseveres, repeat the steps to reseat the printhead up to three times.
On the off chance that the printhead error message endures, proceed to the subsequent stage.

Step 4: Replace the HP printhead

If your carriage has a printhead latch, replace the printhead.

If you have a damaged cartridge or printhead, it may be under guarantee. To check the guarantee on your ink or toner supplies, go to Printer and Page Yield Overview and afterwards audit the restricted guarantee data for your provisions.

On the off chance that your printhead gets together is never again under guarantee, you may have the option to buy another one online.

Go to HP Parts Store.
On the off chance that you are in the Asia Pacific, the site guides you to a service centre in your area.
Search HP Parts Store for your printhead part number. Refer to the following table to find your printhead part number based on the ink cartridge numbers your printer uses.

Follow the online instructions to order the printhead assembly.

If the printhead error message persists, continue to the next step.

Like it? Share it!

About the Author

Mandy rawat
Joined: November 18th, 2019
Articles Posted: 5